MiLAN's new EmPowered Ethernet Series Power over Ethernet Splitter solutions deliver unified supply of data, voice, and video as well as electrical power through a single source by sending power over standard Category 5 and above twisted pair cables. Power over Ethernet simplifies installation and eliminates the need to run separate power cords and LAN cables to each Access Point or port locations. MiLAN's new PoE EmPowered Ethernet Power over Ethernet Splitter provides organizations with affordable, easy-to-use solutions that enable them to migrate their network infrastructure to support a growing number of advanced cost-saving, performance enhancing applications, such as streamlining wireless, VOIP, Network IP camera deployments, and centralized power backup solutions. Whether on a factory floor or in an enterprise facility, running power to hard to reach locations with MiLAN's Power over Ethernet solutions significantly reduce cabling and outlet requirements while providing the lowest total cost of ownership.

deliver unified supply of data, voice, and video as well as electrical power through a single source by sending power over standard Category 5 and above twisted pair cables. Power over Ethernet simplifies installation and eliminates the need to run separate power cords and LAN cables to each Access Point or port locations.

IntelliJack Switch to 48-Volt VoIP Phone Power Module, enable 3Com IntelliJack Switches to forward compatible power, as well as data, to select 48-Volt VoIP phones, Low-profile module. Converts the voltage and signal detection of the incoming 802.3af Power over Ethernet.

The 3Com Power over Ethernet Single-Port Midspan Solution can power an IEEE 802.3af compliant device, such as the 3Com Network Jack or IntelliJack Switch, over standard Category 5 or 5e Ethernet cabling. This 48-volt inline power source installs right in the switch closet, eliminating an exposed power supply and extra wiring at the workspace. Installing Power over Ethernet helps save time and money because it's less vulnerable to damage or tampering than a local power supply.

The 3Com Power over Ethernet Single-Port Midspan Solution can power an IEEE 802.3af compliant device, such as the 3Com Network Jack or IntelliJack Switch, over standard Category 5 or 5e Ethernet cabling. This 48-volt inline power source installs right in the switch closet, eliminating an exposed power supply and extra wiring at the workspace. Installing Power over Ethernet helps save time and money because it's less vulnerable to damage or tampering than a local power supply.

The Linksys 12 Volt Power Over Ethernet Adapter Kit lets you put your access points almost anywhere, by removing the requirement of nearby power outlets. By using the existing Category 5 Ethernet cabling to deliver power to many standard 12 volt access points and other network devices, you save the time, hassle, and expense of running AC power to the access point's installation location. The 12 Volt Power Over Ethernet Adapter Kit is a two piece set. The "Injector" sends both power and data over one Category 5 cable to your access point, wireless router or bridge. Then the tiny "Splitter", placed at the remote location, separates the network data and DC power back into two cables, and delivers them to the access point. The Injector can also be used by itself with POE-enabled network devices that accept 48 volts directly on a POE port.

The SMCPWR-INJ3 is an IEEE802.3af compliant PoE (Power over Ethernet) 1-port injector that combines power and data signals. By using the SMCPWR-INJ3, an external power adapter will no longer be required. Utilizing a standard Category 5 Ethernet RJ-45 cable, the power and data can be combined (injected) into the Ethernet RJ45 Cat.5 output cable and feed into the PoE enabled devices to provide both power and data signals. It will reduce your network installation costs and increase the flexibility, especially in locations where electrical power sources are difficult to get.

The SMCAMP-INJ is an IEEE 802.3af Power Injector that provides power to the SMCAMP-250 Amplifier using a standard Category 5 cable. The SMCAMP-INJ delivers power to the Amplifier at a distance up to 100 m (328 feet), while requiring access to only a standard 12 V power source and a Category 5 connection to the network (such as via a hub or switch). In this way, the SMCAMP-INJ reduces installation cost, as a dedicated power outlet is not necessary to be near where the SMCAMP-250 Amplifier is installed. It is convenient, simple, and easy to install.

The Cisco Unified IP Phone Power Injector is a midspan power injector designed and tested for use with Cisco Unified IP phones. The Cisco Unified IP Phone Power Injector sits between a switch port and the Cisco Unified IP phone, providing inline power capability to an unpowered switch port. It supports Cisco midspan power, IEEE 802.3af modes for supplying power to the attached phone, and 10/100/1000BASE-T Ethernet connections.

Cisco Power over Ethernet Injector

Cisco Aironet Power Injector provides Ethernet inline powering as an alternative to local power or inline power capable switches, while also providing improved device and cable organization.

The Power Injector LR2 converts the standard 10/100 BaseT Ethernet category 5 RJ-45 interface that is suitable for weather-protected areas to a dual F-Type connector interface for dual coaxial cables that are more suitable for harsh outdoor environments. While providing a 100baseT interface to the Cisco Aironet 1300 Series, the Power Injector LR2 also provides power to the unit over the same cables with a power discovery feature that protects other appliances from damage should they accidentally be connected. To support longer cable runs from your infrastructure network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable, enabling total cable runs up to 200 meters. Lightning and surge protection is also included at the F-Type connector interface to provide added protection to your network infrastructure devices. The LR2 Power injector requires a Cisco supplied 48V DC source.

The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector, converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector enables total cable runs up to 200 meters (Category 5 Cable + Coax). It is designed for use in transportation applications and operates with an input voltage range of +12 to +40VDC. The DC source is provided by the user. The LR2T can therefore be vehicle or solar powered. The Power Injector provides for installation flexibility when an AC power source is not available.

Reliable: A Power over Ethernet system protected by a UPS eliminates power cuts and ensures that the IP telephone network is always available Economical: Power is supplied to the equipment connected to the IP network via the existing wiring Simple to install: Plug and play installation that requires no configuring Network rack in a data/communications center: The midspan unit can be installed between a standard Ethernet switch and the terminals without modifying the existing wiring It is the ideal solution for updating equipment, quick and easy to install, improved continuity of service, cheaper than adding new PoE switches

Reliable: A Power over Ethernet system protected by a UPS eliminates power cuts and ensures that the IP telephone network is always available Economical: Power is supplied to the equipment connected to the IP network via the existing wiring Simple to install: Plug and play installation that requires no configuring Network rack in a data/communications center: The midspan unit can be installed between a standard Ethernet switch and the terminals without modifying the existing wiring It is the ideal solution for updating equipment, quick and easy to install, improved continuity of service, cheaper than adding new PoE switches

D-Link, an industry leader in networking, introduces the DWL-P200 Power over Ethernet (PoE) Adapter. The DWL-P200 delivers both data and electrical power to Ethernet-enabled devices using a single Ethernet cable. Using Power over Ethernet, you eliminate the need to place an Ethernet-enabled device, such as a wireless access point, near a power outlet, giving you more freedom in placement.

D-Link, an industry leader in networking, introduces the DWL-P50 Power over Ethernet (PoE) Splitter. By using the DWL-P50, both data and electrical power can be delivered to a non-PoE Ethernet-enabled device from a single CAT5 Ethernet cable.

Axis Power over LAN Midspan

Axis 0169-014-01 6 Port Power over Ethernet Midspan

PowerDsine's PD-6024G/AC/M Power over Gigabit Ethernet Midspan(PoE injector) provides safe power over standard Ethernet cabling to both existing 10/100 baseT network devices and emerging Gigabit devices. The PD-6024G/AC/M Power over Gigabit Ethernet Midspan market's first midspan providing power for Gigabit Ethernet devices, such as IP phones,wireless LAN access points and IP network video cameras in enterprise installations,offering long term investment protection by supporting both existing 10/100 baseT devices while ensuring support for future 1000 baseT devices.